澳门国际永利总站网站(欢迎您)

欢迎来访澳门国际永利总站网站官网!
咨询服务热线
0531-88270327 13153168609
资讯中心

滚珠丝杠螺母如何安装滚珠你知道吗?

永利总站/ 日期:2019-12-17 发布人:admin

  你必须有一个相同的套筒和螺旋球槽直径、线的母亲,用煤油清洗后涂上润滑脂在球槽,然后使用抹上一点油针头,针上的球与润滑脂竖起一个接一个球槽,内套丝的母亲完成后,使用螺杆抵抗旋转套筒可以压榨,滚珠螺杆套筒旋入不要挤球。

  You must have a mother with the same sleeve and spiral ball groove diameter and thread. After cleaning with kerosene, apply lubricating grease to the ball groove, and then use a little oil needle. The ball on the needle and lubricating grease stand up one by one ball groove. After the mother of the inner sleeve is finished, use the screw to resist the rotating sleeve to press. The ball screw sleeve can be screwed in without squeezing the ball.
  使用相应的类型的假轴安装,但也相应的类型的钢球,进口耐磨,如16螺杆直径16假轴安装3.175钢球,32螺杆直径32假轴安装6.350钢球,等等滚珠丝杆螺母安装方法的详细步骤:
  Use the corresponding type of dummy shaft installation, but also the corresponding type of steel ball, imported wear-resistant, such as 16 screw diameter, 16 dummy shaft installation, 3.175 steel ball, 32 screw diameter, 32 dummy shaft installation, 6.350 steel ball, and other detailed steps of ball screw nut installation method:
  1. 清洁滚珠丝杆螺母和滚珠轴承。
  1. Clean the ball screw nut and ball bearing.
导轨丝杠
  2. 把塑料珠塞(换向器)放回螺母内。安装止珠器时,应注意止珠器的球形进出口与螺旋槽的光滑连接。
  2. Put the plastic bead plug (commutator) back into the nut. When installing the ball stopper, pay attention to the smooth connection between the ball inlet and outlet of the ball stopper and the spiral groove.
  3.油脂螺母。
  3. Grease nut.
  4. 把球放进螺旋槽里。注意,并不是所有的螺旋槽都被填满,球是按照一个圆型园珠塞的原则放置的,我看到你的坚果似乎是4个圆型园珠塞,也就是4个圆型园珠塞。
  4. Put the ball into the spiral groove. Note that not all the spiral grooves are filled. The ball is placed according to the principle of a round round ball stopper. I see that your nut seems to be four round ball stopper, that is, four round ball stopper.
  5. 将螺帽旋进丝杆(注意不要使滚珠轴承下落)。
  5. Screw the nut into the screw rod (be careful not to drop the ball bearing).
  6. 前后转动螺母,检查螺母运转是否平稳。如果是,它的意思是好的。
  6. Turn the nut back and forth to check whether the nut runs smoothly. If so, it means good.
  滚珠丝杠螺母安装滚珠其他方法
  Other methods of ball screw nut installation首先,不建议自行拆卸和安装螺母,特别是高导球丝杠。
  First of all, it is not recommended to remove and install nuts by yourself, especially the high guide ball screw.
  在发生意外损失的螺母或如果你已经删除了螺母,重新安装螺母如下:一个空心套筒外径略小于直径的螺丝底部水沟(约0.1毫米小),一个内径略大于螺杆的外径较大(0.5 ~ 2毫米),和一个长度超过螺母的长度(10 ~ 50毫米长)。
  In case of accidental loss of the nut or if you have deleted the nut, reinstall the nut as follows: a hollow sleeve with the outer diameter slightly smaller than the diameter of the screw bottom ditch (about 0.1mm small), an inner diameter slightly larger than the outer diameter of the screw (0.5 ~ 2mm), and a length longer than the nut (10 ~ 50mm long).
  空集装在泡沫类软对象结束时,穿入洗干净没有滚珠螺母,然后把干净的每个圆槽成一个球,装满了一圈(gap以0.5 ~ 1.5球直径大小为宜)轻轻旋转空心套管,确认后顺利,然后推动下的空心西装一圈,直到完全填满。
  At the end of the foam soft object, the empty container is put into a ball without a ball nut, and then each clean round groove is made into a ball, which is filled with a circle (gap should be 0.5 ~ 1.5 ball diameter). Rotate the hollow sleeve gently, confirm it is smooth, and then push the hollow suit for a circle until it is completely filled.
  拆卸的填料塞,插入空心套筒螺帽螺杆轴的结束,空心套筒用一只手,螺杆上的螺母螺钉另一方面,直到所有坚果顺利螺钉进入有效螺纹槽螺钉的一部分。更后,将油脂或润滑油注入螺母注油孔,并将螺母全行程移动2次以上,保证运转平稳。更后,再次注入润滑脂,完成操作。
  Remove the packing plug, insert the hollow sleeve nut at the end of the screw shaft, and use one hand for the hollow sleeve, on the other hand for the nut screw on the screw, until all nuts smoothly enter a part of the effective threaded slot screw. Finally, grease or lubricating oil shall be injected into the nut filling hole, and the nut shall be moved for more than 2 times in full stroke to ensure smooth operation. Finally, inject grease again to complete the operation.
  以上是导轨丝杠制造商为大家先容的相关内容,想要了解更多内容,欢迎访问网站:These are the related contents introduced by the guide screw manufacturer. For more information, please visit the website: http://www.jgongrun.com

澳门国际永利总站网站