澳门国际永利总站网站(欢迎您)

欢迎来访澳门国际永利总站网站官网!
咨询服务热线
0531-88270327 13153168609
资讯中心

进口导轨的故障排除大家知道吗

永利总站/ 日期:2020-04-07 发布人:admin

  生产导轨丝杠本标准适用于灯具与二极管或多极导体连接到导轨系统的力量,包括接地装置(I型),每个导体额定电流不超过16,和导轨系统的电极间的额定电压不超过440 V或地面(m),提供每一个额定电流的导体不得超过25,公称安全特低电压不超过25v轨道系统。导轨系统为灯具提供机械支撑。本标准适用于一般室内使用的导轨系统,包括安装、嵌入或悬挂在墙壁和天花板上的导轨系统。这些导轨系统不打算用于经常发生特殊情况的地方,例如船舶、汽车等,也不打算用于不好的地方,例如可能发生爆炸的危险地方。本标准应使用结合参考标准gb7000.1。如果遇到进口导轨的故障,怎样才能有效的排除?

导轨丝杠
  This standard is applicable to the strength of lamps and diodes or multipole conductors connected to the guide rail system, including the grounding device (type I), the rated current of each conductor shall not exceed 16, the rated voltage between the electrodes of the guide rail system shall not exceed 440V or the ground (m), the conductor providing each rated current shall not exceed 25, and the nominal safe extra low voltage shall not exceed 25V. The rail system provides mechanical support for the lamps. This standard is applicable to the guide rail system for general indoor use, including the guide rail system installed, embedded or hung on the wall and ceiling. These guide rail systems are not intended to be used in places where special circumstances often occur, such as ships, automobiles, etc., or in places where they are not good, such as places where explosion may occur. This standard shall use the combined reference standard gb7000.1. If there is a problem with the imported guide rail, how can it be effectively eliminated?
  工业导轨主要由钢或铸铁制成。在长期的使用过程中,由于两个接触面之间存在不同程度的摩擦,导轨表面会产生不同程度的划痕和应变,严重影响设备的加工精度和生产效率。传统的修补方法通常采用金属板贴面或更换的方法,但需要大量的精密加工制造和手工刮磨。维修过程多,工期长。针对机床导轨的划痕和应变问题,可以采用高分子复合材料来解决。由于其优异的附着力、抗压强度、耐油性和耐磨性,该材料可以为构件提供长期的保护层。只需几个小时就可以修复导轨损坏的部分并投入使用。与传统方法相比,操作简单,成本低。
  Industrial rails are mainly made of steel or cast iron. In the long-term use process, due to the existence of different degrees of friction between the two contact surfaces, the surface of the guide rail will produce different degrees of scratches and strains, seriously affecting the processing accuracy and production efficiency of the equipment. The traditional repair method usually uses the method of metal plate veneering or replacement, but it needs a lot of precision manufacturing and manual scraping. There are many maintenance processes and long construction period. In view of the scratch and strain problems of machine tool guide rail, polymer composite material can be used to solve them. Because of its excellent adhesion, compressive strength, oil resistance and wear resistance, the material can provide a long-term protective layer for components. The damaged part of the guide rail can be repaired and put into use in only a few hours. Compared with the traditional method, the operation is simple and the cost is low.
  以上是导轨丝杠制造商为大家先容的相关内容,想要了解更多内容,欢迎访问网站:
  These are the related contents introduced by the guide screw manufacturer. For more information, please visit the website: http://www.jgongrun.com

澳门国际永利总站网站